<div dir="ltr"><div>I only pressed the power switch after I tried different monitors and power supplies (I misstated the rated amperage of the power supply I am currently using - it is 3A instead of 2.5A).</div><div><br></div><div>I just turned it on - left it on for a minute then pressed the power switch - nothing appeared to happen the one LED that was on (D1 - next to the button) did not flicker - I have never seen D2 go on.</div><div><br></div><div>r</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Thu, Oct 22, 2015 at 5:11 PM, Rico Miledi <span dir="ltr"><<a href="mailto:rico.miledi@biodot.com" target="_blank">rico.miledi@biodot.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div>Yes - nothing seemed to change.</div><span class="HOEnZb"><font color="#888888"><div><br></div><div>r</div></font></span></div><div class="HOEnZb"><div class="h5"><div class="gmail_extra"><br><div class="gmail_quote">On Thu, Oct 22, 2015 at 4:12 PM, David Byte <span dir="ltr"><<a href="mailto:dbyte@suse.com" target="_blank">dbyte@suse.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">



<div dir="auto">
<div>Did you press the power button near the blue LEDs?<br>
<br>
Sent from my iPhone. Typos are Apple's fault. </div><div><div>
<div><br>
On Oct 22, 2015, at 6:10 PM, Rico Miledi <<a href="mailto:rico.miledi@biodot.com" target="_blank">rico.miledi@biodot.com</a>> wrote:<br>
<br>
</div>
<blockquote type="cite">
<div>
<div dir="ltr">
<div>I have been trying to follow the setup procedures for a new MinnowBoard Max as described on:</div>
<div><font size="2">
<p><a href="http://wiki.minnowboard.org/MinnowBoard_MAX_HW_Setup" target="_blank">http://wiki.minnowboard.org/MinnowBoard_MAX_HW_Setup</a></p>
<p>I have a 2.5Amp AC to 5V DC power supply (positive on the inside of the barrel) that shows a voltage of 5.4V without a load (just using a multi-meter) and have tried several monitors but each of these reports no signal input.</p>
<p>The board shows only has one illuminated led light when power is applied - I believe that there should be two?</p>
<p>Is the board defective or should I be doing something else (it was purchased recently from Mouser).</p>
<p>Thank you in advance for any help.</p>
<p>Rico</p>
</font></div>
</div>
</div>
</blockquote>
</div></div><blockquote type="cite">
<div><span>_______________________________________________</span><br>
<span>elinux-MinnowBoard mailing list</span><br>
<span><a href="mailto:elinux-MinnowBoard@lists.elinux.org" target="_blank">elinux-MinnowBoard@lists.elinux.org</a></span><br>
<span><a href="http://lists.elinux.org/mailman/listinfo/elinux-minnowboard" target="_blank">http://lists.elinux.org/mailman/listinfo/elinux-minnowboard</a></span><br>
</div>
</blockquote>
</div>

<br>_______________________________________________<br>
elinux-MinnowBoard mailing list<br>
<a href="mailto:elinux-MinnowBoard@lists.elinux.org" target="_blank">elinux-MinnowBoard@lists.elinux.org</a><br>
<a href="http://lists.elinux.org/mailman/listinfo/elinux-minnowboard" target="_blank" rel="noreferrer">http://lists.elinux.org/mailman/listinfo/elinux-minnowboard</a><br>
<br></blockquote></div><br></div>
</div></div></blockquote></div><br></div>