[MinnowBoard] Minnownoard max design with Gerber fils and install it
zahra rahimkhani
zrahimkhani2014 at gmail.com
Tue Nov 8 10:53:04 UTC 2016
John
Thank you for your response.
I will replace my soc with a new soc from a Minnowboard Max board that
i had bought in the past.
Also I use spi flash on Minnowboard Max board and get it on my board.
your opinion, is it right ?
Also LEDs turn on without delay. LEDs turn on immediately .RESET key do not
work .
I programmed spi flash with firmware debug but serial port do not show
something .
On Tue, Nov 8, 2016 at 3:49 AM, John Hawley <john.hawley at intel.com> wrote:
> Ok that looks like it's the E3825, so that looks like it should
> alleviate that as an issue (wanted to make sure that it was a compatible
> part, just on the off chance it wasn't)
>
> Memory part, at first glance anyway, looks right. I'd have to go do a
> lot more digging to be 100% sure there.
>
> Storage processor vs. mobile processor is a little odd, I'd need some
> more context on what you are referring to. The chips are are using are
> based on the Baytrail-I skus, or the industrial version of the skus.
> There are some other Baytrail skus, but most of them are not footprint
> compatible with the Baytrail-I (can't remember which one off hand).
> Pretty sure, given the part number you last gave, you've got the right SoC.
>
> Have you tried flashing the debug firmware in and seeing if anything
> comes out of the serial port?
>
> Unless something is horribly shorted, you are getting both LEDs so the
> SoC should be online, but you are clearly just not getting past
> something in the early start-up, and it's hard to tell, or even guess,
> without something further.
>
> So here's my suggested next steps:
> - If you can flash the debug firmware on the board, and see if you get
> anything out of the serial port (J4)
>
> - If you don't get anything out of the serial port with the debug
> firmware the only other step I can reasonably think of is to go and snag
> a full IDP/XDP (plus the debug lure) and start debugging it that way,
> but this is not an inexpensive way to go, so I would start with trying
> the debug firmware, and let me see what else I can find in the mean time.
>
> - John 'Warthog9' Hawley
>
> On 11/06/2016 10:08 PM, zahra rahimkhani wrote:
> > Dear john
> >
> > Part number soc is FH8065301567313 SR1X9
> > can you suggest a solve?
> >
> > Thank you
> >
> > On Sun, Nov 6, 2016 at 2:08 PM, zahra rahimkhani
> > <zrahimkhani2014 at gmail.com <mailto:zrahimkhani2014 at gmail.com>> wrote:
> >
> > john
> >
> > why it is very important about part number soc ?
> >
> > i bought it from a sale, she is free today ,i send information it
> > tomorrow.
> >
> > Thank you
> >
> > On Sun, Nov 6, 2016 at 11:00 AM, John 'Warthog9' Hawley
> > <warthog9 at eaglescrag.net <mailto:warthog9 at eaglescrag.net>> wrote:
> >
> > Firmware is from that location, just snag the debug version and
> > flash that.
> >
> > As for the link, I need where you bought the SoC itself from, as
> the
> > numbers you've provided don't match anything I can track down.
> >
> > - John 'Warthog9' Hawley
> >
> > On 11/06/2016 12:14 AM, zahra rahimkhani wrote:
> > > john
> > > can you check link?
> > > and firmware ?
> > >
> > > Thank you
> > >
> > > On Sun, Nov 6, 2016 at 10:16 AM, zahra rahimkhani
> > > <zrahimkhani2014 at gmail.com <mailto:zrahimkhani2014 at gmail.com>
> > <mailto:zrahimkhani2014 at gmail.com
> > <mailto:zrahimkhani2014 at gmail.com>>> wrote:
> > >
> > > i used this link , it have Gerber files for v2
> > >
> > > http://wiki.minnowboard.org/MinnowBoard_MAX
> > <http://wiki.minnowboard.org/MinnowBoard_MAX>
> > > <http://wiki.minnowboard.org/MinnowBoard_MAX
> > <http://wiki.minnowboard.org/MinnowBoard_MAX>>
> > >
> > > Also , I used this link for firmware
> > >
> > > https://firmware.intel.com/projects/minnowboard-max
> > <https://firmware.intel.com/projects/minnowboard-max>
> > > <https://firmware.intel.com/projects/minnowboard-max
> > <https://firmware.intel.com/projects/minnowboard-max>>
> > >
> > > Thank you
> > >
> > >
> > >
> > > On Sun, Nov 6, 2016 at 10:08 AM, John 'Warthog9' Hawley
> > > <warthog9 at eaglescrag.net <mailto:warthog9 at eaglescrag.net>
> > <mailto:warthog9 at eaglescrag.net
> > <mailto:warthog9 at eaglescrag.net>>> wrote:
> > >
> > > Can you give me a link to the Baytrail you used, the
> number you list
> > > doesn't come up on anything useful.
> > >
> > > As for debug firmware you'll need to flash it in just
> as you did
> > > with
> > > the stock firmware, you can snag it from the same
> place you
> > > snagged the
> > > default firmware (which is up on the Intel firmware
> site)
> > >
> > > - John
> > >
> > > On 11/05/2016 11:33 PM, zahra rahimkhani wrote:
> > > > I want to check clock for Ram and spi flash ?
> > > >
> > > > do you agree or disagree ?
> > > >
> > > > Thank you so much
> > > >
> > > > On Thu, Nov 3, 2016 at 11:26 AM, zahra rahimkhani
> > > > <zrahimkhani2014 at gmail.com <mailto:
> zrahimkhani2014 at gmail.com>
> > <mailto:zrahimkhani2014 at gmail.com
> > <mailto:zrahimkhani2014 at gmail.com>>
> > > <mailto:zrahimkhani2014 at gmail.com
> > <mailto:zrahimkhani2014 at gmail.com>
> > > <mailto:zrahimkhani2014 at gmail.com <mailto:
> zrahimkhani2014 at gmail.com>>>>
> > wrote:
> > > >
> > > > -I use the Max Gerber files
> > > > -The both of Leds are on but them have not delay
> when they are
> > > > turning on .
> > > > -It was got with BJA device.
> > > > _I used BAYTRAIL-IFH8065301567311.
> > > > -Nothing do not come on serial port
> > > > -I do not know how debug frimwear .
> > > > -I can not sure about BGA components How check
> them ?
> > > >
> > > > On 03/11/2016 10:49 AM, "John 'Warthog9' Hawley"
> > > > <warthog9 at eaglescrag.net <mailto:
> warthog9 at eaglescrag.net>
> > <mailto:warthog9 at eaglescrag.net <mailto:warthog9 at eaglescrag.net
> >>
> > > <mailto:warthog9 at eaglescrag.net
> > <mailto:warthog9 at eaglescrag.net>
> > > <mailto:warthog9 at eaglescrag.net
> > <mailto:warthog9 at eaglescrag.net>>>> wrote:
> > > >
> > > > - Did you use the MAX or the Turbot Gerber
> > files?
> > > > - Do either of the LEDs (D1, D2) come on
> > when power is applied?
> > > > - Did you get the SoC itself placed
> correctly?
> > > > - Which SoC are you using?
> > > > - Which RAM chips are you using?
> > > > - Does anything come out on the serial port
> > during boot?
> > > > - Have you tried with the debug firmware?
> > > > - Are you sure there isn't a short on the
> > pcb itself?
> > > >
> > > > If you can answer that it should get us a
> > good starting point on
> > > > trying to help you with what you are seeing.
> > > >
> > > > - John 'Warthog9' Hawley
> > > >
> > > > On 11/3/2016 12:01 AM, zahra rahimkhani
> wrote:
> > > >
> > > > Hello
> > > > I make a minnowboard max with use from
> > GERBER files on its
> > > > website .
> > > >
> > > > but it do not work . i tested all of
> > voltages . they are
> > > > correct .
> > > > also freamwear was programmed by a
> > programmer on chip 1.8 v
> > > >
> > > > but it is not work . please suggest a
> solve?
> > > >
> > > > thank you
> > > >
> > > >
> > > >
> > _______________________________________________
> > > > elinux-MinnowBoard mailing list
> > > > elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>
> > > <mailto:elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>>
> > > >
> > <mailto:elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>
> > > <mailto:elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>>>
> > > >
> > > http://lists.elinux.org/mailman/listinfo/elinux-
> minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> > > <http://lists.elinux.org/mailman/listinfo/elinux-
> minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>>
> > > > <http://lists.elinux.org/
> mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> > > <http://lists.elinux.org/mailman/listinfo/elinux-
> minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>>>
> > > >
> > > > ______________________________
> _________________
> > > > elinux-MinnowBoard mailing list
> > > > elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>
> > > <mailto:elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>>
> > > > <mailto:elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>
> > > <mailto:elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>>>
> > > >
> > >
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> > >
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>>
> > > >
> > >
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> > >
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>>>
> > > >
> > > >
> > > >
> > > >
> > > > _______________________________________________
> > > > elinux-MinnowBoard mailing list
> > > > elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>
> > > <mailto:elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>>
> > > >
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> > >
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>>
> > > >
> > >
> > > _______________________________________________
> > > elinux-MinnowBoard mailing list
> > > elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>
> > > <mailto:elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>>
> > >
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> > >
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>>
> > >
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > elinux-MinnowBoard mailing list
> > > elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>
> > > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> > >
> >
> > _______________________________________________
> > elinux-MinnowBoard mailing list
> > elinux-MinnowBoard at lists.elinux.org
> > <mailto:elinux-MinnowBoard at lists.elinux.org>
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> > <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> >
> >
> >
> >
> >
> > _______________________________________________
> > elinux-MinnowBoard mailing list
> > elinux-MinnowBoard at lists.elinux.org
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >
> _______________________________________________
> elinux-MinnowBoard mailing list
> elinux-MinnowBoard at lists.elinux.org
> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.elinux.org/pipermail/elinux-minnowboard/attachments/20161108/c2b1af86/attachment-0001.html>
More information about the elinux-MinnowBoard
mailing list