[MinnowBoard] Minnownoard max design with Gerber fils and install it

[zahra rahimkhani]

john
can you check link?
and firmware ?

Thank you

On Sun, Nov 6, 2016 at 10:16 AM, zahra rahimkhani <zrahimkhani2014 at gmail.com
> wrote:

> i used this link , it have Gerber files for v2
>
> http://wiki.minnowboard.org/MinnowBoard_MAX
>
> Also , I used this link for firmware
>
> https://firmware.intel.com/projects/minnowboard-max
>
> Thank you
>
>
>
> On Sun, Nov 6, 2016 at 10:08 AM, John 'Warthog9' Hawley <
> warthog9 at eaglescrag.net> wrote:
>
>> Can you give me a link to the Baytrail you used, the number you list
>> doesn't come up on anything useful.
>>
>> As for debug firmware you'll need to flash it in just as you did with
>> the stock firmware, you can snag it from the same place you snagged the
>> default firmware (which is up on the Intel firmware site)
>>
>> - John
>>
>> On 11/05/2016 11:33 PM, zahra rahimkhani wrote:
>> > I want to check clock for Ram and spi flash ?
>> >
>> > do you agree or disagree ?
>> >
>> > Thank you so much
>> >
>> > On Thu, Nov 3, 2016 at 11:26 AM, zahra rahimkhani
>> > <zrahimkhani2014 at gmail.com <mailto:zrahimkhani2014 at gmail.com>> wrote:
>> >
>> >     -I use the Max Gerber files
>> >     -The both of Leds are on but them have not delay when they are
>> >     turning on .
>> >     -It was got with BJA device.
>> >     _I used BAYTRAIL-IFH8065301567311.
>> >     -Nothing do not come on serial port
>> >     -I do not know  how debug frimwear .
>> >     -I can not sure about BGA components How check them ?
>> >
>> >     On 03/11/2016 10:49 AM, "John 'Warthog9' Hawley"
>> >     <warthog9 at eaglescrag.net <mailto:warthog9 at eaglescrag.net>> wrote:
>> >
>> >         - Did you use the MAX or the Turbot Gerber files?
>> >         - Do either of the LEDs (D1, D2) come on when power is applied?
>> >         - Did you get the SoC itself placed correctly?
>> >         - Which SoC are you using?
>> >         - Which RAM chips are you using?
>> >         - Does anything come out on the serial port during boot?
>> >         - Have you tried with the debug firmware?
>> >         - Are you sure there isn't a short on the pcb itself?
>> >
>> >         If you can answer that it should get us a good starting point on
>> >         trying to help you with what you are seeing.
>> >
>> >         - John 'Warthog9' Hawley
>> >
>> >         On 11/3/2016 12:01 AM, zahra rahimkhani wrote:
>> >
>> >             Hello
>> >             I make  a minnowboard  max with use from GERBER files on its
>> >             website .
>> >
>> >             but it do not work . i tested all of voltages . they are
>> >             correct .
>> >             also freamwear was programmed by a programmer on chip 1.8 v
>> >
>> >             but it is not work . please suggest a solve?
>> >
>> >             thank you
>> >
>> >
>> >             _______________________________________________
>> >             elinux-MinnowBoard mailing list
>> >             elinux-MinnowBoard at lists.elinux.org
>> >             <mailto:elinux-MinnowBoard at lists.elinux.org>
>> >             http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>> >             <http://lists.elinux.org/mailman/listinfo/elinux-minnowboar
>> d>
>> >
>> >         _______________________________________________
>> >         elinux-MinnowBoard mailing list
>> >         elinux-MinnowBoard at lists.elinux.org
>> >         <mailto:elinux-MinnowBoard at lists.elinux.org>
>> >         http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>> >         <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
>> >
>> >
>> >
>> >
>> > _______________________________________________
>> > elinux-MinnowBoard mailing list
>> > elinux-MinnowBoard at lists.elinux.org
>> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>> >
>>
>> _______________________________________________
>> elinux-MinnowBoard mailing list
>> elinux-MinnowBoard at lists.elinux.org
>> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.elinux.org/pipermail/elinux-minnowboard/attachments/20161106/186980d9/attachment.html>