[MinnowBoard] Minnownoard max design with Gerber fils and install it

[zahra rahimkhani]

i used this link , it have Gerber files for v2

http://wiki.minnowboard.org/MinnowBoard_MAX

Also , I used this link for firmware

https://firmware.intel.com/projects/minnowboard-max

Thank you



On Sun, Nov 6, 2016 at 10:08 AM, John 'Warthog9' Hawley <
warthog9 at eaglescrag.net> wrote:

> Can you give me a link to the Baytrail you used, the number you list
> doesn't come up on anything useful.
>
> As for debug firmware you'll need to flash it in just as you did with
> the stock firmware, you can snag it from the same place you snagged the
> default firmware (which is up on the Intel firmware site)
>
> - John
>
> On 11/05/2016 11:33 PM, zahra rahimkhani wrote:
> > I want to check clock for Ram and spi flash ?
> >
> > do you agree or disagree ?
> >
> > Thank you so much
> >
> > On Thu, Nov 3, 2016 at 11:26 AM, zahra rahimkhani
> > <zrahimkhani2014 at gmail.com <mailto:zrahimkhani2014 at gmail.com>> wrote:
> >
> >     -I use the Max Gerber files
> >     -The both of Leds are on but them have not delay when they are
> >     turning on .
> >     -It was got with BJA device.
> >     _I used BAYTRAIL-IFH8065301567311.
> >     -Nothing do not come on serial port
> >     -I do not know  how debug frimwear .
> >     -I can not sure about BGA components How check them ?
> >
> >     On 03/11/2016 10:49 AM, "John 'Warthog9' Hawley"
> >     <warthog9 at eaglescrag.net <mailto:warthog9 at eaglescrag.net>> wrote:
> >
> >         - Did you use the MAX or the Turbot Gerber files?
> >         - Do either of the LEDs (D1, D2) come on when power is applied?
> >         - Did you get the SoC itself placed correctly?
> >         - Which SoC are you using?
> >         - Which RAM chips are you using?
> >         - Does anything come out on the serial port during boot?
> >         - Have you tried with the debug firmware?
> >         - Are you sure there isn't a short on the pcb itself?
> >
> >         If you can answer that it should get us a good starting point on
> >         trying to help you with what you are seeing.
> >
> >         - John 'Warthog9' Hawley
> >
> >         On 11/3/2016 12:01 AM, zahra rahimkhani wrote:
> >
> >             Hello
> >             I make  a minnowboard  max with use from GERBER files on its
> >             website .
> >
> >             but it do not work . i tested all of voltages . they are
> >             correct .
> >             also freamwear was programmed by a programmer on chip 1.8 v
> >
> >             but it is not work . please suggest a solve?
> >
> >             thank you
> >
> >
> >             _______________________________________________
> >             elinux-MinnowBoard mailing list
> >             elinux-MinnowBoard at lists.elinux.org
> >             <mailto:elinux-MinnowBoard at lists.elinux.org>
> >             http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >             <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >
> >
> >         _______________________________________________
> >         elinux-MinnowBoard mailing list
> >         elinux-MinnowBoard at lists.elinux.org
> >         <mailto:elinux-MinnowBoard at lists.elinux.org>
> >         http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >         <http://lists.elinux.org/mailman/listinfo/elinux-minnowboard>
> >
> >
> >
> >
> > _______________________________________________
> > elinux-MinnowBoard mailing list
> > elinux-MinnowBoard at lists.elinux.org
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >
>
> _______________________________________________
> elinux-MinnowBoard mailing list
> elinux-MinnowBoard at lists.elinux.org
> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.elinux.org/pipermail/elinux-minnowboard/attachments/20161106/eb69ab5c/attachment-0001.html>