[MinnowBoard] using DLP-USB1232H, verification error. is it due to DP_IO3L in SPI header not connected ?
Sathish Kumar Balasubramaniam -ERS, HCL Tech
b-sathishkumar at hcl.com
Tue Apr 19 05:31:16 UTC 2016
John,
I have another clarification.
What is the use of the DDP_IO3L pin on the SPI header ?
Is it need to be connected to the programmer to read, write and erase or it depends upon the chip ?
I am getting this doubt since Dediprog connects to this pin while FT2232H/flashrom programmer does not connect to this pin as per their website.
Regards,
B.Sathish Kumar
-----Original Message-----
From: Sathish Kumar Balasubramaniam -ERS, HCL Tech
Sent: 19 April 2016 01:42
To: MinnowBoard Development and Community Discussion <elinux-minnowboard at lists.elinux.org>
Subject: RE: [MinnowBoard] using DLP-USB1232H, verification error. is it due to DP_IO3L in SPI header not connected ?
Thanks very much, John, for the clarification.
I understood the problem :(
OK. I will check it.
Thanks,
B.Sathish Kumar
________________________________________
From: elinux-MinnowBoard [elinux-minnowboard-bounces at lists.elinux.org] on behalf of John Hawley [john.hawley at intel.com]
Sent: 19 April 2016 01:35:44
To: elinux-minnowboard at lists.elinux.org
Subject: Re: [MinnowBoard] using DLP-USB1232H, verification error. is it due to DP_IO3L in SPI header not connected ?
Correct, that's likely the problem. There's no level shifters between the pins and the chip itself, it won't really harm it to run it at 3.3v, but what you are seeing is indicative that it's not working correctly (and what I remember seeing when I tried it myself). You will either need something like a Dediprog, or a SPI Hook that can run at 1.8v, or level shift all of the pins from the DLP-USB1232H down to 1.8v for this to work.
- John
On 04/18/2016 12:57 PM, Sathish Kumar Balasubramaniam -ERS, HCL Tech wrote:
> John,
>
> Though I am giving 1.8v to SPI flash header, the CS, SCLK, MISO and
> MOSI comes from DLP-USB1232H which may be using 3.3v ??? not sure May be this is the problem ?
> If so, how can I turn these 3.3v to 1.8v in DLP-USB1232H ?
>
>
> Regards,
> B.Sathish Kumar
>
> ________________________________________
> From: elinux-MinnowBoard [elinux-minnowboard-bounces at lists.elinux.org]
> on behalf of John Hawley [john.hawley at intel.com]
> Sent: 19 April 2016 01:25:53
> To: elinux-minnowboard at lists.elinux.org
> Subject: Re: [MinnowBoard] using DLP-USB1232H, verification error. is it due to DP_IO3L in SPI header not connected ?
>
> Are your logic pins running at 1.8V, or just feeding 1.8v into pin 1?
>
> On 04/18/2016 12:39 PM, Sathish Kumar Balasubramaniam -ERS, HCL Tech wrote:
>> John,
>>
>> I have a voltage regulator which has 1.8v (1.78v in digital meter) and it is given to the SPI flash header.
>>
>> Regards,
>> B.Sathish Kumar
>> ________________________________________
>> From: elinux-MinnowBoard
>> [elinux-minnowboard-bounces at lists.elinux.org] on behalf of John
>> Hawley [john.hawley at intel.com]
>> Sent: 19 April 2016 01:05:45
>> To: elinux-minnowboard at lists.elinux.org
>> Subject: Re: [MinnowBoard] using DLP-USB1232H, verification error. is it due to DP_IO3L in SPI header not connected ?
>>
>> Are you doing 1.8v or 3.3v into the MAXes SPI flash header? The part
>> is setup (on the MAX) for 1.8v operation, so what you might be seeing
>> is it not operating correctly due to over voltage.
>>
>> - John
>>
>> On 04/18/2016 12:27 PM, Sathish Kumar Balasubramaniam -ERS, HCL Tech wrote:
>>> forgot to add env info
>>>
>>> OS: Ubuntu 14.04.4 64bit
>>> flashrom version - 0.9.9
>>>
>>
>>
>> ::DISCLAIMER::
>> ---------------------------------------------------------------------
>> ---------------------------------------------------------------------
>> ----------
>>
>> The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only.
>> E-mail transmission is not guaranteed to be secure or error-free as
>> information could be intercepted, corrupted, lost, destroyed, arrive
>> late or incomplete, or may contain viruses in transmission. The e mail and its contents (with or without referred errors) shall therefore not attach any liability on the originator or HCL or its affiliates.
>> Views or opinions, if any, presented in this email are solely those
>> of the author and may not necessarily reflect the views or opinions
>> of HCL or its affiliates. Any form of reproduction, dissemination,
>> copying, disclosure, modification, distribution and / or publication of this message without the prior written consent of authorized representative of HCL is strictly prohibited. If you have received this email in error please delete it and notify the sender immediately.
>> Before opening any email and/or attachments, please check them for viruses and other defects.
>>
>> ---------------------------------------------------------------------
>> ---------------------------------------------------------------------
>> ----------
>>
>> _______________________________________________
>> elinux-MinnowBoard mailing list
>> elinux-MinnowBoard at lists.elinux.org
>> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>>
> _______________________________________________
> elinux-MinnowBoard mailing list
> elinux-MinnowBoard at lists.elinux.org
> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> _______________________________________________
> elinux-MinnowBoard mailing list
> elinux-MinnowBoard at lists.elinux.org
> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>
_______________________________________________
elinux-MinnowBoard mailing list
elinux-MinnowBoard at lists.elinux.org
http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
More information about the elinux-MinnowBoard
mailing list