[MinnowBoard] MinnowBoard Max - no Input signal on screen

[Rico Miledi]

Thank you all - I was pretty sure the board had an issue but Mouser told me
to contact Minnowboard.

I am sending it back and requesting another.

r

On Fri, Oct 23, 2015 at 2:13 PM, John Hawley <john.hawley at intel.com> wrote:

> If D2 isn't turning on I'd go ahead and file an RMA.
>
> - John 'Warthog9' Hawley
>
> On 10/23/2015 01:55 PM, maxreyesr at gmail.com wrote:
> > There is a FTDI seríal port on minnowboard max for those cases to find a
> > solution even without input signal on screen...
> >
> > El 23/10/2015 14:34, "Rico Miledi" <rico.miledi at biodot.com
> > <mailto:rico.miledi at biodot.com>> escribió:
> >
> >     I was looking at the TinCanTools flasher, however as the board is
> >     brand new I do not see why I should need to do this.
> >     I was looking for confirmation that the board is bad and I think I
> >     have just received it - thank you.
> >
> >     r
> >
> >     On Fri, Oct 23, 2015 at 11:47 AM, Eric <ericolv at cox.net> wrote:
> >
> >         Sounds like the first one I bought (still dead).   I had to send
> >         it back, they re-flashed it and sent it back.  It worked for a
> >         while then went dead again.  If you have a SPI flasher, you can
> >         try to re-flash the board (SPI Hook TinCanTools.com or DediProg
> >         SF 100, the first one is /much/ cheaper).  However, this did not
> >         work for mine.    ____
> >
> >         __ __
> >
> >         *From:*elinux-MinnowBoard
> >         [mailto:elinux-minnowboard-bounces at lists.elinux.org] *On Behalf
> >         Of *Rico Miledi
> >         *Sent:* Thursday, October 22, 2015 5:39 PM
> >         *To:* MinnowBoard Development and Community Discussion
> >         *Subject:* Re: [MinnowBoard] MinnowBoard Max - no Input signal
> >         on screen____
> >
> >         __ __
> >
> >         I only pressed the power switch after I tried different monitors
> >         and power supplies (I misstated the rated amperage of the power
> >         supply I am currently using - it is 3A instead of 2.5A).____
> >
> >         __ __
> >
> >         I just turned it on - left it on for a minute then pressed the
> >         power switch - nothing appeared to happen the one LED that was
> >         on (D1 - next to the button) did not flicker - I have never seen
> >         D2 go on.____
> >
> >         __ __
> >
> >         r____
> >
> >         __ __
> >
> >         On Thu, Oct 22, 2015 at 5:11 PM, Rico Miledi
> >         <rico.miledi at biodot.com> wrote:____
> >
> >         Yes - nothing seemed to change.____
> >
> >         __ __
> >
> >         r____
> >
> >         __ __
> >
> >         On Thu, Oct 22, 2015 at 4:12 PM, David Byte <dbyte at suse.com>
> >         wrote:____
> >
> >         Did you press the power button near the blue LEDs?
> >
> >         Sent from my iPhone. Typos are Apple's fault. ____
> >
> >
> >         On Oct 22, 2015, at 6:10 PM, Rico Miledi
> >         <rico.miledi at biodot.com> wrote:____
> >
> >             I have been trying to follow the setup procedures for a new
> >             MinnowBoard Max as described on:____
> >
> >             http://wiki.minnowboard.org/MinnowBoard_MAX_HW_Setup____
> >
> >             I have a 2.5Amp AC to 5V DC power supply (positive on the
> >             inside of the barrel) that shows a voltage of 5.4V without a
> >             load (just using a multi-meter) and have tried several
> >             monitors but each of these reports no signal input.____
> >
> >             The board shows only has one illuminated led light when
> >             power is applied - I believe that there should be two?____
> >
> >             Is the board defective or should I be doing something else
> >             (it was purchased recently from Mouser).____
> >
> >             Thank you in advance for any help.____
> >
> >             Rico____
> >
> >             _______________________________________________
> >             elinux-MinnowBoard mailing list
> >             elinux-MinnowBoard at lists.elinux.org
> >
> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard____
> >
> >
> >         _______________________________________________
> >         elinux-MinnowBoard mailing list
> >         elinux-MinnowBoard at lists.elinux.org
> >         http://lists.elinux.org/mailman/listinfo/elinux-minnowboard____
> >
> >         __ __
> >
> >         __ __
> >
> >
> >         _______________________________________________
> >         elinux-MinnowBoard mailing list
> >         elinux-MinnowBoard at lists.elinux.org
> >         http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >
> >
> >
> >     _______________________________________________
> >     elinux-MinnowBoard mailing list
> >     elinux-MinnowBoard at lists.elinux.org
> >     <mailto:elinux-MinnowBoard at lists.elinux.org>
> >     http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >
> >
> >
> > _______________________________________________
> > elinux-MinnowBoard mailing list
> > elinux-MinnowBoard at lists.elinux.org
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >
> _______________________________________________
> elinux-MinnowBoard mailing list
> elinux-MinnowBoard at lists.elinux.org
> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.elinux.org/pipermail/elinux-minnowboard/attachments/20151023/cc94f95e/attachment.html>