[MinnowBoard] no suitable video mode found booting in blind mode

[nb]

I’m sorry Lucas, I don’t remember.
As it was my first Minnowboard, I tried many things and don’t remembre much.
But I’m sure that Graphical install didn’t work.
I also remember that my SSD was not detected in some kinds of install.
But once I found the good way to install, everything went fine.
I think that « Advanced install » was the one which worked.

Regards

nb


> Le 21 mai 2015 à 23:56, Luca <l.cappe at gmail.com> a écrit :
> 
> Hi, 
> 
> i've tried also "text install". Can you confirm that also this didn't work during your test?
> 
> Thanks,
> 
> Luca.
> 
> 2015-05-21 23:50 GMT+02:00 nb <nb at dagami.org>:
> Hi Luca,
> 
> I can say that for a reason I can’t explain, Debian graphical install is not possible via FDTI.
> I trie it some time ago and it didn’t work.
> It’s possible only via micro-HDMI
> 
> Hope this helps
> 
> nb
> 
> 
> > Le 21 mai 2015 à 23:34, Luca <l.cappe at gmail.com> a écrit :
> >
> > Hi Ken,
> >
> > i don't use mouse, keyboard and monitor, because i haven't the HDMI<->microHDMI cable.
> > So i'm using the serial port (FDTI 232 3.3V, 4 wire).
> > The response are "yes it works", i'm able to enter in UEFI Interactive Shell for all steps.
> > For the step 2, i'm able to see the device in the boot list (fs0), for the step 3 i don't see the device in the list.
> >
> > Luca.
> >
> > 2015-05-21 23:23 GMT+02:00 Ken Tait <ktait at venturesystemdesign.com>:
> > Luca,
> >
> > Well that clearly sounds like something else is not right here..3A should be enough.
> >
> > Let's get back to basics..
> >
> > Step 1:
> > Connect->bare board, power supply, monitor, keyboard and mouse. NO boot device or USB keys.
> > DO NOT CONNECT THE NETWORK HERE...
> >
> > Does this come up in the bios or boot shell?? Yes or NO...
> >
> > Does it clearly see your mouse and keyboard & monitor..this is fairly critical?
> >
> > Step 2:
> > if this comes up, remove power, add a boot device(SD card prefered)...what happens?
> > Does this work. Yes or No?
> >
> > Step 3: Remove SD card if it worked, try USB boot device.
> > Does this work. Yes or NO.
> >
> > You have to take this step by step and see where it's going off the rails, you have too many variables now..
> >
> > Regards
> >
> > Ken
> >
> > _______________________________________________
> > elinux-MinnowBoard mailing list
> > elinux-MinnowBoard at lists.elinux.org
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> >
> > _______________________________________________
> > elinux-MinnowBoard mailing list
> > elinux-MinnowBoard at lists.elinux.org
> > http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> 
> _______________________________________________
> elinux-MinnowBoard mailing list
> elinux-MinnowBoard at lists.elinux.org
> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard
> 
> _______________________________________________
> elinux-MinnowBoard mailing list
> elinux-MinnowBoard at lists.elinux.org
> http://lists.elinux.org/mailman/listinfo/elinux-minnowboard